Mr-Glass Door Installation Nationwide | Sightline Windows & Doors Pembroke Pines

Mr-Glass Door Installation: The Pembroke Pines Owner’s Guide

Mr-Glass door installation in Pembroke Pines typically runs $1,200-$2,800 for a standard replacement, with most projects completed in one working day. We stock Mr-Glass-compatible hardware, seals, and frame components on our trucks, and we carry the full catalog for the 600 Series, 800 Series, and Select lines. Most Pembroke Pines homeowners discover their Mr-Glass door needs attention when the sweep gap widens enough to let water through during summer storms, or when the multipoint lock stops engaging after years of settling frame stress.

Call (754) 219-8346

Which Mr-Glass Models This Applies To

Mr-Glass organizes its door offerings into three series that matter for replacement planning. The 600 Series uses a 2-inch frame depth with a single-fin weatherstrip design; the 800 Series steps to 2.5 inches with a dual-fin compression seal and a heavier-duty hinge backset. The Select line, their impact-rated offering, carries a reinforced jamb and a proprietary multipoint locking mechanism that does not interchange with the standard 600 or 800 hardware.

To identify your series, check the hinge-side jamb label. Mr-Glass stamps a four-digit code: 6xxx for 600, 8xxx for 800, SLxx for Select. The date code matters too. Pre-2019 600 Series units used a 3/4-inch sweep that Mr-Glass discontinued; the current replacement is 7/8-inch, which means the sill cap often needs adjustment or replacement to maintain proper compression. We have run into this exact mismatch in Pembroke Falls homes where original 2016-2018 builds are hitting their first hardware cycle.

We are an independent service provider, not affiliated with Mr-Glass. For OEM parts, we order through their verified distribution channel; for hardware that has been superseded or discontinued, we source equivalent-grade components that meet the original U-factor and air-infiltration specs. The multipoint lock bodies on Select doors are one place where we insist on OEM, no exceptions. The strike geometry is too specific.

Before

After

Signs Your Mr-Glass Door Installation Is Failing

• Visible daylight under the door when closed. The sweep or sill cap has compressed past recovery. On Mr-Glass units, the PVC sweep fin typically holds shape for 6-8 years in Pembroke Pines’ UV exposure, then cracks at the fold point. Water follows the crack inward during driving rain.
• Multipoint lock handle turns but deadbolts do not extend. The gearbox inside the lock body has stripped, usually from repeated operation while the door is out of plumb. The 600 and 800 Series share a gearbox; Select uses a different mechanism entirely. A failed gearbox means the door is latched but not secured.
• Door drags or sticks seasonally. Florida’s humidity cycle swells the jamb slightly, but if the door was shimmed too tight at install, the slab binds against the frame. We see this most in west-facing Pembroke Pines units where afternoon heat expansion compounds the issue.
• Condensation between glass lites on a multipanel door. The insulated glass unit (IGU) seal has failed. Mr-Glass uses a dual-seal system; outer seal failure lets moisture in, inner seal failure lets argon out. The IGU needs replacement, not the whole door, but the sizing must be confirmed before ordering because slab thickness varies by series.
• Hinge screws backing out or hinge leaves separating from the jamb. The original fasteners were undersized for the weight of impact-rated glass, or the jamb material has fatigued. This is structural; a longer screw or toggle is not the fix if the jamb itself is splitting.

Replacement Cost & What’s Included

Mr-Glass door installation pricing in Pembroke Pines breaks down as follows:

What drives the range: frame condition, whether the rough opening needs remediation, and whether the original install left adequate shimming space. Every quote we write in Pembroke Pines starts with a measured survey you keep. The price on that document matches the final invoice; Haven Clause 1 does not allow drift. Parts carry the manufacturer’s warranty; our labor carries the 365-Day Done Right Promise under the Haven Standard. If the sweep compresses unevenly or the lock does not seat clean, we return and correct it.

DIY or Call Us?

There is one thing an owner can safely verify: the jamb label. Read the series code, note the date, and photograph any visible damage. That information saves time on the phone.

Everything else carries risk. A Mr-Glass Select door with impact-rated glass weighs 180-240 pounds depending on lite configuration; removing it without proper support risks slab damage and personal injury. The multipoint lock mechanism stores spring tension; disassembly without the correct release sequence can launch internal components. And the IGU replacement requires a clean-room-level work surface; any grit between the new glass and the sash gasket creates a pressure point that cracks the lite within months.

We have cleaned up enough partial DIY attempts in Pembroke Pines to know where the line sits. Call (754) 219-8346 and we will schedule a measured survey. The written price arrives before any tool is lifted.

FAQs